Ways To Cut Curly Hair – smartesthairstyles.com – When cutting curly hair, you need to judge the curls individually rather than cutting them as a unit. Failure to use special curly hair techniques can result in a pyramid shape or extra frizz. Whether you want to cut someone else’s hair or your own hair, you can use a variety of techniques to get the results you want.
- Started
Get your supplies. You need good cutting scissors. They should be very sharp as dull scissors will not make a good cut. You’ll also need bobby pins, clips, or hair ties if you want to section off part of your hair, and a wide-toothed comb.
Only use your hair clippers to cut hair. Using them for other things will dull them, making it difficult to trim your hair.
Skip razors because they can make curly hair frizzier.
Detangle your hair. Hair is easiest to detangle when it’s slightly wet. Use a wide-toothed comb, not a brush, or a regular comb. Start at the roots and work your way down, gently teasing out tangles with the comb.
If a tangle is particularly stubborn, see if it needs a little trimming to untangle it.
Work on dry or mostly dry hair. While you can wash your hair beforehand, you should work with dry hair when cutting curls. This way it’s easier to cut exactly what you want as the length alternates between dry and wet.
Some stylists say moisture works well too. Mainly it means less drying time. Just make sure the curls are mostly scrunched up before you start cutting so you can get an idea of the shape.
Another option is to spritz dry hair with a light leave-in conditioner, giving you the best of both worlds.
- Cut your own hair
Try the 2 section bob. If you are looking for a short bob, start by washing and drying your hair. You might want to add some leave-in conditioner. Comb your hair into a low ponytail at the back of your head. Don’t bring it too close to your head.
Make sure to comb any loose hair and make the hair as straight as possible. Once you’ve combed it into a ponytail, pull the elastic down an inch or two. Section your hair straight below the ponytail holder.
Release the ponytail. Comb your hair into a high ponytail at the very top of your head. Once you’ve combed everything straight, also trim across the top, about two inches from the end of your hair.
Comb out, done.
Try to search and destroy with a mirror. This method works better in front of a mirror that magnifies. That way you can really see what you’re doing. The goal of search and destroy is to simply remove what is damaged.
“Dusting” is lighter than a trim, which means you won’t lose as much weight.
Work on small, discrete sections of your hair at a time. Hold them up to the mirror so you can see which ones are damaged.
Cut off the ends of the damaged curls. Once you have all the damaged ends in one section, move on to the next section.
Pin back any areas you’ve already trimmed.
Search and destroy using the twist method. Start with detangled hair. Twist your hair into small sections. That is, wrap the hair around your finger until it exposes the damaged ends. Cut what you can.
Make sure your hair is dry or just damp before beginning this method.
You can also do this method with small braids. Your sections should only be about an inch by an inch. Cut off 1/4 inch to 1/2 inch.
Pin or tie back areas you have already trimmed.
Use your fingers to seek and destroy. Another way to find damage is to feel for it with your fingers. As you run your fingers through your hair, feel for damaged ends. If you find any, cut off the piece.
This method also works best on dry or damp hair.
When you’ve completed an area, pin it.
- Trimming or dusting someone else’s hair
Divide it into small sections. When parting, twist or braid the hair to keep it in the small sections. You can also use small clips if you prefer.
Small sections work best for this method as it makes the hair easier to work with.
Try sections about 1″ x 1″ but if your hair is thinner you can go a little larger.
Work on one section at a time. At each section, unbraid or clip. Comb it out and layer it between your fingers. Stretch it out until it’s straight and you only have the ends extending from your fingertips.
Be careful not to use a brush as this can frizz the hair. Stick to a wide-toothed comb.
Cut or dust as much as you like. “Dusting” refers to removing only the damaged ends, while “trimming” means cutting off a little more. Is both ok It just depends on the person’s preferences.
With your hair between your fingers, cut off the excess ends. Walk across in a straight line. The straight line can work here as it is only a very small section of hair.
Move overhead. When doing so, make sure to re-pin the sections you’ve already edited. You don’t want to do the same section twice.
You can use bigger hair clips to pull back the already trimmed hair.
You can rebraid or twist sections so they don’t get in the way when you cut them.
Carry out a final check. When you’re done trimming, undo any rotations. Shake out the hair to ensure no large hairs are sticking out. With curly hair, you won’t have perfectly aligned hair, but trim off any obviously thick or long pieces.
- Cutting someone else’s hair
Have the person lean their head back. One way to work curly hair is to let the person sit back. Pull the top layer of hair into your hand and let the edges hang out.
You can have the person fold forward instead.
The point of this technique is to create instant layers of light.
Cut the hair. With the hair in your hand, section at an angle towards your hand and clip the ends. You won’t get every hair. With curly hair, you don’t always have to cut a straight line like with straight hair.
One method you can use is to comb out a section. Hold the hair with your fingers and move it towards the ends. Instead of cutting what’s held between your fingers, cut on the other side of your hand. Cut at a downward angle, moving toward your fingers, being careful not to cut yourself. This technique helps create texture.
Thin it out a bit. Where hair looks voluminous, pull out individual curls for trimming. Cut inward at an angle, just like you did when you flipped the hair.
Basically, you will just keep pulling out curls to trim the ends a bit until the hair doesn’t look so voluminous.
make shifts. Layers help set curly hair into shape. Long layers often work well, with the shortest layer starting at chin length and the remaining layers going down from there.
But you can also go very short. Just make sure it’s at least 2 inches across the person’s entire head. As you cut, shape the hair so that it follows the shape of the person’s head.
Others swear by short layers, with the top layer being 5 to 6 inches long. You need to find what works best for each hair type.
The flipping technique helps add natural layers to the hair. So if you’re happy with that, you don’t need to add any more layers. To add layers, work your way through hair and trim from top to bottom.
However, you can also use clips to edit individual layers at once. Section up most of the hair to work on the bottom layer. Pull out some for the next part and work on that layer. Continue until you have as many levels as you want.
Cut off all dead ends. Although flipping the hair helps form the layers of hair, it doesn’t take care of dead ends in the bottom layer. Go around the bottom and pull out any hair you see with dead or split ends.
Pull the hair through your fingers and clip the ends.
Look at the head as a whole. When you’re done, do one final check. Look for larger stray hairs and clip away anything that doesn’t belong. Be sure to look directly at the person so you can see where the problem is, and don’t forget to check the back as well.